E-flite Ascent 450 Brushless PNP Bedienungsanleitung

SpecificationsWingspan: 54 in (1370mm)Wing Area: 330 sq in (21.4 sq dm)Length: 32 in (825mm)Weight w/ Battery: 18–19 oz (510–540 kg)Weight w/o Bat

10 E-flite Ascent PNP Assembly Manual 5. Use a felt-tipped pen to transfer the outline of the fuselage onto the top of the stabilizer. 6. Remove t

11E-flite Ascent PNP Assembly Manual 8. Step back and view the airframe from roughly 8-10 feet (2-3 meters) to check the alignment of the stabilizer

12 E-flite Ascent PNP Assembly Manual 2. Use a felt-tipped pen to transfer the edge of the fuselage onto the bottom of the fin. 3. Use a felt-tipp

13E-flite Ascent PNP Assembly Manual 5. Use a hobby knife with a new #11 blade to remove the covering from the bottom of the fin.Important: Use ligh

14 E-flite Ascent PNP Assembly Manual 8. Use 6-minute epoxy to glue the fin to the fuselage.  9. Use painter's tape to keep the fin in positi

15E-flite Ascent PNP Assembly Manual 12. Use medium CA to glue the skid to the bottom of the stabilizer.Receiver InstallationRequired PartsReceiver

16 E-flite Ascent PNP Assembly Manual 2. Plug the elevator servo, rudder servo and speed control leads into the appropriate ports of the receiver. O

17E-flite Ascent PNP Assembly ManualControl Throws 1. Turn on the transmitter and receiver of your Ascent 450 BL Park Glider PNP®. Check the movemen

18 E-flite Ascent PNP Assembly ManualRange Test Your Radio 1. Please consult your radio instructions for complete range testing instructions. 2. D

19E-flite Ascent PNP Assembly ManualGlide Testing Your Ascent PNPWe strongly recommend that before you fly your new Ascent, you first perform a test g

2 E-flite Ascent PNP Assembly ManualIntroductionThank you for purchasing the Ascent™ 450 BL Park Glider. E-flite’s Ascent offers the modeler a PNP (Pl

20 E-flite Ascent PNP Assembly ManualThermal SoaringA key component to soaring is the air mass the park glider flies in. Also, there is an energy sour

21E-flite Ascent PNP Assembly ManualSometimes the wind will cause the thermal to bend or break, causing a warm air bubble that slowly travels downwind

22 E-flite Ascent PNP Assembly ManualExecuting a 180-degree turnThe second method is to make a wide 180-degree turn back into the thermal.Flying the

23E-flite Ascent PNP Assembly ManualIn-Flight Adjustments for Performance and Conditions• Pitch Attitude• Minimum Sink Speed• Maximum Lift/Drag (L/D)

24 E-flite Ascent PNP Assembly ManualMinimum Sink SpeedIn our discussion of thermals, we know sink is the cooler air moving downward to replace the wa

25E-flite Ascent PNP Assembly Manual2008 Official AMA National Model Aircraft Safety CodeGENERAL1) I will not fly my model aircraft in sanctioned ev

26 E-flite Ascent PNP Assembly Manual

27E-flite Ascent PNP Assembly Manual

13398© 2008 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 (877) 504-0233 horizonhobby.com E-fliteRC.com

3E-flite Ascent PNP Assembly ManualContents of Kit/Parts LayoutReplacement PartsEFL2701 Wing SetEFL2702 FuselageEFL2703 Tail SetEFL2704 CanopyEFL2

4 E-flite Ascent PNP Assembly ManualOptional AccessoriesEFLA110 Power MeterNotes Regarding Servos and ESCWARNING: Use of servos other than those we r

5E-flite Ascent PNP Assembly ManualDamage LimitsHORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCT

6 E-flite Ascent PNP Assembly ManualNon-Warranty RepairsShould your repair not be covered by warranty the repair will be completed and payment will be

7E-flite Ascent PNP Assembly ManualWing AssemblyRequired PartsFuselage Wing panel (right and left)Aluminum wing tube #4 washer (2)4-40 x 1/2-inch so

8 E-flite Ascent PNP Assembly Manual 4. The wing will fit tight against the fuselage when installed. 5. Use two 4-40 x 1/2-inch socket head screws

9E-flite Ascent PNP Assembly Manual 2. Mark the center of the tail boom inside the boom using a felt-tipped pen. 3. Use painter's tape to sec