SpecificationsWingspan: 62 in (1570mm)Length: 62.5 in (1580mm)Wing Area: 740 sq in (47.7 sq dm)Weight w/o Battery: 9.2–10.5 lb (4.2–4.7 kg)Weight
10 E-flite Deuces Wild Assembly ManualRudder and Elevator linkage InstallationRequired PartsFuselage assembly Nylon clevis (2)Silicone clevis retaine
11E-flite Deuces Wild Assembly Manual 4. Center the elevator servo using the radio system. With the elevator in the neutral position, use a felt-tip
12 E-flite Deuces Wild Assembly Manual 7. Next, slide the pushrod keeper onto the wire. Slide the horn and keeper down so the horn it tight against
13E-flite Deuces Wild Assembly Manual 11. Thread a clevis onto one of the 29 3/4-inch (755mm) pushrod wires. Make sure to slide a silicone clevis re
14 E-flite Deuces Wild Assembly Manual 14. Make a 90 degree bend in the pushrod wire at the mark you made in Step 10. 15. Slide the pushrod wire t
15E-flite Deuces Wild Assembly Manual 16. Slide the pushrod keeper onto the wire. Position the wire so the bend in the wire is snug against the cont
16 E-flite Deuces Wild Assembly ManualAileron Servo InstallationRequired PartsWing panel (right and left) Servo hatch (right and left)Servo mounting
17E-flite Deuces Wild Assembly Manual 3. Position the servo between the blocks. Leave a small gap between the servo and hatch to prevent the transf
18 E-flite Deuces Wild Assembly Manual 6. Attach the servo to the servo mounting blocks using the screws provided with the servo and a #1 Phillip
19E-flite Deuces Wild Assembly Manual 10. Secure the servo hatch to the wing using four 2mm x 10mm self tapping screws and a #1 Phillips screwdrive
2 E-flite Deuces Wild Assembly ManualIntroductionThe Deuces Wild 25e2 ARF is the first twin and the first sport plane in the Platinum Series. It is ea
20 E-flite Deuces Wild Assembly Manual 14. Use pliers to bend the pushrod 90-degrees at the mark made in the previous step. 15. Slide the pushro
21E-flite Deuces Wild Assembly ManualFlap Servo InstallationRequired PartsWing center section Servo w/hardwareBrass pushrod connector Nylon connecto
22 E-flite Deuces Wild Assembly Manual 4. Secure the flap servo in the wing using a #1 Phillips screwdriver and the hardware provided with the servo.
23E-flite Deuces Wild Assembly Manual 8. Secure the connector using a nylon connector backplate. You may trim the servo horn with side cutters to re
24 E-flite Deuces Wild Assembly Manual 12. Make sure the flap servo is in the up position using the radio system. Move the flaps to the up position an
25E-flite Deuces Wild Assembly ManualHalf Flap: Full Flap:
26 E-flite Deuces Wild Assembly ManualFixed Gear InstallationRequired PartsWing center section Fuselage assemblyMain gear (right and left) Nose gear
27E-flite Deuces Wild Assembly Manual 2. Use a drill and 3/32-inch (2.5mm) drill bit to drill the locations for the four screws. 3. Apply 2–3 dr
28 E-flite Deuces Wild Assembly Manual 6. Position the nose landing gear in the opening in the fuselage. Use a pencil to transfer the locations for
29E-flite Deuces Wild Assembly Manual 10. Connect the clevis to the center hole of the nose wheel steering arm. 11. Slide the pushrod wire into th
3E-flite Deuces Wild Assembly ManualContents of Kit/Parts LayoutReplacement PartsEFL4551L Left Wing PanelEFL4551C Center Wing PanelEFL4551R Right W
30 E-flite Deuces Wild Assembly Manual 14. Slide the brass pushrod connector in the hole drilled in the previous step. 15. Secure the connector to
31E-flite Deuces Wild Assembly ManualRetract Gear InstallationRequired PartsWing center section Fuselage assemblyNose gear retract Main gear retract
32 E-flite Deuces Wild Assembly Manual 3. Position the nose landing gear in the opening in the fuselage. Use a pencil to transfer the locations for
33E-flite Deuces Wild Assembly Manual 7. Locate the steering cable and two crimps. Use side cutters to cut the cable into two equal lengths. Slide a
34 E-flite Deuces Wild Assembly Manual 10. Remove the wheel from the fixed nose gear using a #2 Phillips screwdriver to loosen the screw that secu
35E-flite Deuces Wild Assembly Manual 13. Secure the connectors to the servo horn using a nylon connector backplates. 14. Center the steering ser
36 E-flite Deuces Wild Assembly Manual 16. Cut a 3-inch (76mm) piece of air line and attach it to the air fill fitting. 17. Use a hobby knife to r
37E-flite Deuces Wild Assembly Manual 20. Use silicone adhesive to secure the air tank in the fuselage. The air line between the air fill fitting an
38 E-flite Deuces Wild Assembly Manual 22. Use a covering iron to iron the covering inside the edges of the retract opening. 23. Position the ma
39E-flite Deuces Wild Assembly Manual 26. Cut a 10-inch (254mm) piece of air line. Attach the air line to the fitting on the main gear retract.
4 E-flite Deuces Wild Assembly ManualRequired Tools and AdhesivesTools & EquipmentFelt-tipped pen Ball driver: 3/32-inchLow-tack masking tape Mi
40 E-flite Deuces Wild Assembly Manual 29. Slide a 3/16-inch wheel collar without a screw onto the main gear wire, then the wheel. Use a 3/16-inch
41E-flite Deuces Wild Assembly ManualHint: Cut the string routed through the wing into two pieces and tape them to the wing as shown to keep them out
42 E-flite Deuces Wild Assembly Manual 5. Secure the retract servo in the wing using the hardware provided with the servo and a #1 Phillips screwdri
43E-flite Deuces Wild Assembly Manual 9. Attach a T-fitting to the air line from the previous step. On one side of the T-fitting, attach a 3-inch (7
44 E-flite Deuces Wild Assembly Manual 13. Secure the connector to the servo horn using a nylon connector backplate. You may use side cutters to tri
45E-flite Deuces Wild Assembly Manual 15. Thread a clevis onto a the 3-inch (76mm) pushrod wire. Make sure to slide a silicone clevis retainer onto
46 E-flite Deuces Wild Assembly ManualHint: Try to keep the amounts equal for both up and down. You may need to remove the servo horn and adjust it on
47E-flite Deuces Wild Assembly Manual 2. Tie the string on one side to the end of the throttle and aileron extensions. Repeat for the opposite side.
48 E-flite Deuces Wild Assembly ManualPower 25 Motor InstallationRequired PartsMotor w/X-mount (2) Motor nacelle (right and left)4-40 x 1-inch socket
49E-flite Deuces Wild Assembly ManualPower 32 Motor InstallationRequired PartsMotor w/X-mount (2) Spacer (8)Motor nacelle (right and left)4-40 x 1-in
5E-flite Deuces Wild Assembly ManualNote on Lithium Polymer BatteriesLithium Polymer batteries are significantly more volatile than alkaline or Ni-Cd/
50 E-flite Deuces Wild Assembly Manual 2. Place the X-mount for the motor into the nacelle. Ensure the counter sunk holes in the X-mount face towar
51E-flite Deuces Wild Assembly Manual 5. The screws to attach the X-mount to the motor will need to be installed using the openings from the backsi
52 E-flite Deuces Wild Assembly Manual 7. Repeat Steps 1 through 6 to install the remaining motor in the nacelle.Propeller and Spinner InstallationR
53E-flite Deuces Wild Assembly Manual 1. Pass the adapter for your motor into the spinner backplate. Slide the propeller onto the adapter.Note: It
54 E-flite Deuces Wild Assembly Manual 5. Use hook and loop tape to attach the speed control to the inside of the motor nacelle. 6. Test fit the
55E-flite Deuces Wild Assembly ManualNote: Use paper towels and rubbing alcohol to clean up any excess epoxy that squeezes out from the nacelles onto
56 E-flite Deuces Wild Assembly ManualWing InstallationRequired PartsWing panel (right and left) Wing center sectionWing tube (2) 1/4-20 x 2-inch ny
57E-flite Deuces Wild Assembly Manual 3. With the outer wing panel tight against the wing center section, use a 3/32-inch ball driver to install th
58 E-flite Deuces Wild Assembly Manual 2. Fill the retract system with a commercially available air pump and operate the retracts. With the main ge
59E-flite Deuces Wild Assembly ManualCenter of Gravity and Nose Cone InstallationRequired PartsAirframeNose ConeRequired Tools and AdhesivesCanopy Gl
6 E-flite Deuces Wild Assembly Manual 2. Position the elevator servo in the fuselage. Use a pencil to transfer the locations for the servo mounting
60 E-flite Deuces Wild Assembly ManualControl Throws 1. Turn on the transmitter and receiver of your Deuces Wild. Check the movement of the rudder u
61E-flite Deuces Wild Assembly ManualRange Test Your Radio 1. Before each flying session, be sure to range check your radio. This is accomplished by
62 E-flite Deuces Wild Assembly ManualFlying Your Deuces WildWith the counter-rotating props the elimination of torque delivers straight ahead acceler
63E-flite Deuces Wild Assembly ManualSafety, Precautions, and WarningsAs the user of this product, you are solely responsible for operating it in a ma
64 E-flite Deuces Wild Assembly ManualDamage LimitsHORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PROD
65E-flite Deuces Wild Assembly ManualNon-Warranty RepairsShould your repair not be covered by warranty the repair will be completed and payment will b
66 E-flite Deuces Wild Assembly Manual2008 Official AMA National Model Aircraft Safety CodeGENERAL1) I will not fly my model aircraft in sanctioned
67E-flite Deuces Wild Assembly Manual
13397© 2008 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 (877) 504-0233 horizonhobby.com E-fliteRC.com
7E-flite Deuces Wild Assembly Manual 6. Repeat all of the previous steps to install the rudder servo and steering servo in the fuselage. Note that t
8 E-flite Deuces Wild Assembly Manual 8. Plug a 3-inch (76mm) servo extension into the throttle, aileron and flap ports on the receiver at this time.
9E-flite Deuces Wild Assembly Manual 2. Slide the threaded rods from the fin into the holes in the stabilizer. The fin will fit flush against the st
Kommentare zu diesen Handbüchern