E-flite 80-Amp Pro Switch-Mode BEC Brushless ESC, EC5 Bedienungsanleitung PDF herunterladen

WARNING: Read the ENTIRE instruction manual to become familiar with the

features of the product before operating. Failure to operate the product correctly can result in

damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product and NOT a toy. It must be operated with caution and

common sense and requires some basic mechanical ability. Failure to operate this Product

in a safe and responsible manner could result in injury or damage to the product or other

property. This product is not intended for use by children without direct adult supervision.

Do not attempt disassembly, use with incompatible components or augment product in

any way without the approval of Horizon Hobby, Inc. This manual contains instructions for

safety, operation and maintenance. It is essential to read and follow all the instructions and

warnings in the manual, prior to assembly, setup or use, in order to operate correctly and

avoid damage or serious injury.

Introduction

Thank you for purchasing the E-ﬂite

80-Amp Pro Switch-Mode BEC Brushless ESC. This is

a lightweight, high-quality, efﬁcient sensorless brushless electronic speed control with an

integrated switch-mode BEC. It can operate without the need for a separate receiver battery

to power your servos and receivers, saving you weight and complication. It is capable of up

to 80 amps continuous current when using 3- to 6-series Li-Po battery packs. You can drive

up to 7 analog or 6 digital standard-sized servos with the BEC on any recommended input

voltage. This ESC also features safe power arming along with advanced programmable

features such as low voltage cutoff, braking, timing, throttle input range, and more, making

this truly a ‘pro series’ speed control.

CAUTION: Product may become hot when in use.

Features

• Upto80ampscontinuouscurrentwithproperairowand100ampsburstcurrent(15

seconds)

• 5Vswitch-modeBECcapableof2.5ampscontinuouscurrentonanyrecommended

input voltage

• Driveupto7analogor6digitalstandard-sizedservoswiththeBEConany

recommended input voltage

• 3-to6-cellLi-Po,9-to18-cellNi-MH/Ni-Cdinputvoltage

• Programmablemotorbraking

• Safepower-armmodepreventsaccidentalstarts

• Programmablelowvoltagecutoffwithsettingsfor3-cellLi-Po(9.2V),4-cellLi-Po

(12V),5-cellLi-Po(15V),6-cellLi-Po(18V),or74%ofbatterystartingvoltage

• Programmablethrottleinputrange(1.1ms–1.9msor1.2ms–1.8ms)

• Programmablesoftstart-uprate-.25secondor1second

• Automotorshutdownifsignalislostorthereisinterference

• Programmabletiming—5user-selectableranges–usewithalargevarietyofbrushless

motors

• Twooperatingmodes–AirplaneorHeli

• Pre-wiredconnectors—E-iteEC5onbatteryinputand4.0mmfemalegoldbulletson

motor output leads

Speciﬁcations

Continuous Current: 80A*

MaxBurstCurrent: 100A(15sec)*

Length: 77mm(3.0in)

Width: 41mm(1.60in)

Height: 15.5mm(0.62in)

Weight: 106g(3.75oz)

Cells: 3-6SLi-Poor9-18Ni-MH/Ni-Cd

BatteryInputLeads: 10AWGwithE-iteEC5

™

Connector

MotorOutputLeads: 12AWGwith4.0mmFemaleGold

Bullet Connectors

* Proper cooling required

Servo Ratings with BEC Enabled

Normal recommendation is the ESC drives up to 7 analog or 6 digital standard-sized servos

with the BEC on any recommended input voltage.

Some servo combinations we have tested in various models include:

• 7JR

MC35(JSP20030)analogmicroservos,1JRDS368(JRPS368BB)digitalmicro

servo,3EFL15-25sizeretracts—EFLHabu32

• 6JR537(JRPS537)analogstandardservos—Hangar9

UltraStick40ARF

• 5JRDS811(JRPS811)/JRDS821(JRPS821)digitalstandardservos—SeagullHarrier

463D

• 4JRDS811(JRPS811)/JRDS821(JRPS821)digitalstandardservosand1JR791

(JRPS791)retractservo—Hangar960-sizedwarbirds

• 5JRDS811(JRPS811)/JRDS821(JRPS821)digitalstandardservosand1JR791

(JRPS791)retractservo—Hangar9Spitre60

• 4JRSPORT™MN48(JSP20040)analogminiservos—E-iteDiamante25eARF

• 4JRDS3421(JRPSDS3421)digitalminiservos—E-iteEratix3D25eARF

• 7JRMC35(JSP20030)analogmicroservosand1JRRT88(JSP20080)retract

servo—25-sizedwarbird

Some other brands and models of servos may have signiﬁcantly higher current draw. Digital

servos and binding servos of any kind typically have higher current draw. As a general

rule, micro and sub-micro servos draw less current which may affect your

servo usage as shown in the examples above with different servo combinations

and electric retracts. We recommend the use of a Hangar 9 Servo and

Receiver Current Meter (HAN172), installed between the throttle lead of the

ESC and receiver, to conﬁrm current draw of the actual servos and electric

retracts used. Also, always be sure to position the ESC for maximum airﬂow since cooling

cansignicantlyaidintheperformanceoftheBEC.TheESCisratedforatleast2.5-Amp

continuouscurrentand4-Ampshortbursts.

Before ﬁrst use, please refer to “Servo Ratings with BEC Enabled” notes for BEC usage

guidelines. You must follow these guidelines for safe operation. If you are using more than 7

analog standard servos, more than 6 digital standard servos, or servos with higher current

draw than the BEC can deliver, you may need to disable the BEC. If you wish to disable

the BEC, you must remove the red receiver wire lead and connector from the receiver lead

housing, and then insulate it properly to prevent shorting. When operating with the BEC

disabled,E-iterecommendstheuseofaseparate,high-power,externalBEC(likethe

UltimateBEC),orreceiverpackandswitchusingthefollowingitemstoensuretrouble-free

operation:

1. JR1100mAh4.8VNi-MHreceiverbattery(JRPB4240),orsimilar

2. JRSwitchHarness(JRPA003),orsimilar

Please read these instructions in their entirety before use

Before you connect your ESC and begin ﬂying, take a moment to look it over. The input power

sidehasablack(negative)andred(positive)wirealongwithanE-iteEC5MaleDevice

Connector.Themotorsidehasthree12-gaugewires(blue,red,andblack)with4.0mm

female gold bullet connectors on the ends.

TheblackandredwireswiththeEC5Device(DEV)Connectorwillconnecttoyourpower

battery. The red wire connects to the red wire on your battery pack, the black wire connects

to the black wire on your battery pack. If the wires are reversed, the ESC may be damaged.

YOU MUST ENSURE THAT YOU CONNECT THE BATTERY POLARITY PROPERLY TO

PREVENT DAMAGE TO THE ESC. Reversing polarity will void your warranty, so always

double-checkthisconnection.UseonlyagenuineE-iteEC5Battery(BATT)connectoronthe

batterysoitmatchestheEC5Device(DEV)connectoronthespeedcontrol.Thethrottlelead

connects to the throttle channel on your radio receiver.

WARNING: For your safety, when checking the startup function of the

ESC or making programming changes, please remove the propeller to prevent

any potential injury. You should always treat the motor and propeller as live

and dangerous, remembering it could start at any time, and keep any body

parts, clothing and tools clear of the propeller arc.

WARNING: NEVER LEAVE THE BATTERY CONNECTED WHEN NOT FLYING

THE AIRCRAFT AND ALWAYS REMOVE THE BATTERY FROM THE MODEL BEFORE

CHARGING AND WHEN FINISHED FLYING.

80-Amp Pro Switch-Mode

BEC Brushless ESC Instructions

Notice

All instructions, warranties and other collateral documents are subject to change at the

solediscretionofHorizonHobby,Inc.Forup-to-dateproductliterature,visithttp://www.

horizonhobby.com and click on the support tab for this product.

Meaning of Special Language

The following terms are used throughout the product literature to indicate various

levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical

property damage AND a little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of

physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of

property damage, collateral damage, and serious injury OR create a high probability

of superﬁcial injury.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - 80-Amp Pro Switch-Mode

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product corr

Seite 2

When ﬂying in hot weather, we recommend checking on the condition of the ESC, battery, and motor after each ﬂight. You may want to consider letting th

Seite 3

MotorPoles–14ormoreExpectedPerformance–Goodbalanceofpowerandefciency1. Movethesticktocenter(between1.4and1.6ms)for5seconds,

Seite 4 - USERS IN THE EUROPEAN UNION

If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product, you are advised to return this Produ

Kommentare zu diesen Handbüchern

Keine Kommentare

E-flite 80-Amp Pro Switch-Mode BEC Brushless ESC, EC5 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware E-flite 80-Amp Pro Switch-Mode BEC Brushless ESC, EC5 herunter. E-flite 80-Amp Pro Switch-Mode BEC Brushless ESC, EC5 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware E-flite 80-Amp Pro Switch-Mode BEC Brushless ESC, EC5