E-flite Apprentice 15e PNP Spezifikationen

SpecificationsWingspan: 58 in (1475mm)Length: 37 in (940mm)Wing Area: 525 sq in (33.7 sq dm)Weight w/o Battery: 32–35 oz (910–1000 g)Weight w/Batt

10 E-flite Apprentice PNP Assembly Manual 3. Slide the battery into the battery compartment. The connector will face the back of the airplane. 4.

11E-flite Apprentice PNP Assembly Manual 2. Use an adjustable wrench to remove the nut from the propeller adapter. Set the nut aside so it does not

12 E-flite Apprentice PNP Assembly ManualControl FunctionsRequired PartsTransmitterWe have shown the Spektrum DX5e as an example to illustrate the fun

13E-flite Apprentice PNP Assembly ManualCHECKING THE ELEVATOR (MODE 2) 3. Center the elevator stick. This is the right stick on the transmitter. The

14 E-flite Apprentice PNP Assembly ManualCHECKING THE ELEVATOR (MODE 1) 3. Center the elevator stick. This is the left stick on the transmitter. The

15E-flite Apprentice PNP Assembly ManualCHECKING THE RUDDER (MODE 1 AND 2) 6. Mode 1 (Rudder/Elevator on left stick): Center the rudder stick. Threa

16 E-flite Apprentice PNP Assembly Manual 9. Once the rudder has been trimmed for straight flight, you can now adjust the steering trim of your Appr

17E-flite Apprentice PNP Assembly Manual 12. Check the movement of the aileron using the transmitter. When the aileron/elevator stick (Mode 2 transm

18 E-flite Apprentice PNP Assembly ManualApprentice Nose Heavy -Add Weight to Tail or Move Battery RearwardApprentice Tail Heavy -Add Weight to Nose o

19E-flite Apprentice PNP Assembly Manual 1. Turn the radio on using the power switch on the front of the transmitter and check that the throttle sti

2 E-flite Apprentice PNP Assembly ManualProduct RegistrationRegister your product online at: www.e-fliterc.com/register/Contents of Kit/Parts LayoutE

20 E-flite Apprentice PNP Assembly ManualHigh Rate: 1-inch (25mm) (Up and Down)AILERON THROW 5. Use a ruler to check the control throws on the aile

21E-flite Apprentice PNP Assembly Manual 2. Slide the spinner backplate on the propeller adapter. 3. Install the washer on the propeller shaft.

22 E-flite Apprentice PNP Assembly ManualFlying Your ApprenticeIt is strongly recommended for your first flights to search out the assistance of a qua

23E-flite Apprentice PNP Assembly ManualDAMAGE LIMITSHORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PR

24 E-flite Apprentice PNP Assembly ManualUnited Kingdom:Electronics and engines requiring inspection or repair should be shipped to the following addr

25E-flite Apprentice PNP Assembly Manual8. I will not operate model aircraft carrying pyrotechnic devices which explode burn, or propel a projectile

26 E-flite Apprentice PNP Assembly ManualDeclaration of ConformityHorizon Hobby, Inc. 4105 Fieldstone Road Champaign, IL 61822 USADeclaration of Confo

27E-flite Apprentice PNP Assembly ManualBuilding and Flying Notes:

Printed 02/0914963.1© 2009 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 (877) 504-0233 horizonhobby.com E-fliteRC.com

3E-flite Apprentice PNP Assembly ManualRequired Radio EquipmentThe Apprentice PNP requires a 4-channel transmitter and full-range receiver. Users of S

4 E-flite Apprentice PNP Assembly ManualAR6200 Receiver InstallationRequired PartsFuselage assembly Hook and loop tapeAR6200 Receiver with remote rec

5E-flite Apprentice PNP Assembly Manual 2. Slide the pins on the bottom of the fin through the holes of the stabilizer and into those in the fuselag

6 E-flite Apprentice PNP Assembly ManualLanding Gear InstallationRequired PartsFuselage assembly Nose gear w/wheelMain gear w/wheelsRequired ToolsPhi

7E-flite Apprentice PNP Assembly Manual 2. Separate the wing panels. Mix 1/2-ounce (15mL) of 30-minute epoxy and apply it to the root of both the le

8 E-flite Apprentice PNP Assembly Manual 6. Make sure the two wing panels are pressed tightly together with no gap between them. Position the front

9E-flite Apprentice PNP Assembly Manual 12. Install the first two rubber bands. They should cross as shown in the image below. 13. The next two ru