E-flite Ultimate 3D Profile ARF Bedienungsanleitung

Ultimate EP 3D Profile and Tribute EP 3D ProfileInstruction Manual

11❍ 3. Use foam-safe CA to glue the stabilizer into the fuselage.❍ 4. Use foam-safe CA to glue the elevator to the balsa elevator joiner. Use the incl

11❍ 3. Use foam-safe CA to glue the stabilizer into the fuselage.❍ 4. Use foam-safe CA to glue the elevator to the balsa elevator joiner. Use the incl

13❍ 3. Wrap the gear retaining thread around the landing gear and landing gear block. Use as much of the thread as possible, as this is the only thing

13❍ 3. Wrap the gear retaining thread around the landing gear and landing gear block. Use as much of the thread as possible, as this is the only thing

15Rudder and Elevator LinkagesRequired PartsFuselage Control horn (2)Pushrod guide (12) Pushrod wire (2)Control horn backplate (2) Double-sided tap

15Rudder and Elevator LinkagesRequired PartsFuselage Control horn (2)Pushrod guide (12) Pushrod wire (2)Control horn backplate (2) Double-sided tap

17❍ 5. Attach a control horn onto the rudder using a control horn backplate. Add a few drops of foam safe CA to the horn to secure it in place.❍ 6. At

17❍ 5. Attach a control horn onto the rudder using a control horn backplate. Add a few drops of foam safe CA to the horn to secure it in place.❍ 6. At

19Wing InstallationRequired PartsWing FuselageRequired Tools and AdhesivesSquare Foam-safe CANote: The installation of the wing for the Tribute and

19Wing InstallationRequired PartsWing FuselageRequired Tools and AdhesivesSquare Foam-safe CANote: The installation of the wing for the Tribute and

3WarningAn RC aircraft is not a toy! If misused, it can cause serious bodily harm and damage to property. Fly only in open areas, preferably at AMA (A

21Top Wing Installation (Ultimate)Required PartsTop wing FuselageWing strut (2)Required Tools and AdhesivesSquare Foam-safe CA❍ 1. Locate the two wi

21Top Wing Installation (Ultimate)Required PartsTop wing FuselageWing strut (2)Required Tools and AdhesivesSquare Foam-safe CA❍ 1. Locate the two wi

23❍ 2. Make an L-bend in one end of the remaining pushrod wire. Attach the wire to the control horn using a micro pushrod keeper.❍ 3. Center one ailer

23❍ 2. Make an L-bend in one end of the remaining pushrod wire. Attach the wire to the control horn using a micro pushrod keeper.❍ 3. Center one ailer

25Ultimate Aileron Connection LinkageRequired PartsAirframe Control horn (4)Control horn back plate (4) Aileron wireMicro pushrod keeper (4)Required

25Ultimate Aileron Connection LinkageRequired PartsAirframe Control horn (4)Control horn back plate (4) Aileron wireMicro pushrod keeper (4)Required

27❍ 4. Secure the pushrod to the control horn using a micro pushrod keeper. Trim the excess wire.❍ 5. Repeat Steps 1 through 4 for the opposite ailero

27❍ 4. Secure the pushrod to the control horn using a micro pushrod keeper. Trim the excess wire.❍ 5. Repeat Steps 1 through 4 for the opposite ailero

29❍ 2. Slide the gearbox assembly onto the gearbox mounting block. Use a hobby knife to make a pilot hole for the 2mm x 6mm screw. Secure the gearbox

29❍ 2. Slide the gearbox assembly onto the gearbox mounting block. Use a hobby knife to make a pilot hole for the 2mm x 6mm screw. Secure the gearbox

3WarningAn RC aircraft is not a toy! If misused, it can cause serious bodily harm and damage to property. Fly only in open areas, preferably at AMA (A

31Note: You may need to change the connectors on the speed control to match those of the motor or battery. Also be careful of the spinning propeller.❍

31Note: You may need to change the connectors on the speed control to match those of the motor or battery. Also be careful of the spinning propeller.❍

33Setting up for 3D flightPeople often spend a tremendous amount of time constructing a perfectly straight airplane only to neglect the radio installa

33Setting up for 3D flightPeople often spend a tremendous amount of time constructing a perfectly straight airplane only to neglect the radio installa

35FlyingNow that the airplane is set up correctly, it is time to fine-tune the setup in the air. Start by flying the airplane on low rates. If you hav

35FlyingNow that the airplane is set up correctly, it is time to fine-tune the setup in the air. Start by flying the airplane on low rates. If you hav

37Another common misnomer is that the ailerons do not work while hovering. This could not be further from the truth. If you do not use the ailerons du

37Another common misnomer is that the ailerons do not work while hovering. This could not be further from the truth. If you do not use the ailerons du

393) At all flying sites a straight or curved line(s) must be established in front of which all flying takes place with the other side for spectators.

393) At all flying sites a straight or curved line(s) must be established in front of which all flying takes place with the other side for spectators.

4 5Contents of Kit/Parts LayoutUltimate Replacement Parts:Fuselage w/Rudder EFL2027Wing Set w/Struts EFL2026Horizontal Tail Assembly EFL2028Wheel P

© 2004 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 (877) 504-0233 www.horizonhobby.com

4 5Contents of Kit/Parts LayoutUltimate Replacement Parts:Fuselage w/Rudder EFL2027Wing Set w/Struts EFL2026Horizontal Tail Assembly EFL2028Wheel P

6 7Before Starting AssemblyBefore beginning the Assembly of your Ultimate or Tribute, remove each part from its bag for inspection. Closely inspect th

6 7Before Starting AssemblyBefore beginning the Assembly of your Ultimate or Tribute, remove each part from its bag for inspection. Closely inspect th

98Decal InstallationRequired PartsFuselage WingElevator/stabilizer DecalsBrushed vs. Brushless MotorsThe included 370 motor is designed for use with

98Decal InstallationRequired PartsFuselage WingElevator/stabilizer DecalsBrushed vs. Brushless MotorsThe included 370 motor is designed for use with