SpecificationsWingspan: 34.0 in (865mm)Wing Area: 310 sq in (19.4 sq dm)Length: 26.5 in (672mm)Weight w/o Battery: 7.20–7.50 oz (204–212 g)Weight
10 E-flite Fokker DVII 250 Slow Flyer Assembly Manual 2. Slide the tab on the micro control horn through the elevator from the bottom side as shown
11E-flite Fokker DVII 250 Slow Flyer Assembly Manual 8. Slide the tail assembly in position on the fuselage. Make sure the hinge on the rudder goes
12 E-flite Fokker DVII 250 Slow Flyer Assembly Manual 3. Slide a micro pushrod keeper onto the wire extending through the control horn. 4. The p
13E-flite Fokker DVII 250 Slow Flyer Assembly Manual 9. Use a #1 Phillips screwdriver to tighten the 1.5mm machine screw that will secure the pushro
14 E-flite Fokker DVII 250 Slow Flyer Assembly ManualScale Accessory InstallationRequired PartsAirframe Machine gun (right and left)Required Tools an
15E-flite Fokker DVII 250 Slow Flyer Assembly Manual 3. Set the top wing in place and align the trailing edges looking down from above. You will not
16 E-flite Fokker DVII 250 Slow Flyer Assembly Manual 3. Use foam-safe CA to glue the outer strut to the top and bottom wing after checking the fit
17E-flite Fokker DVII 250 Slow Flyer Assembly Manual 4. Make sure the receiver is out of the way of the landing gear area as well as the connector f
18 E-flite Fokker DVII 250 Slow Flyer Assembly ManualRigging InstallationRequired PartsAirframe Rigging threadMotor battery Hook and loop tape Requi
19E-flite Fokker DVII 250 Slow Flyer Assembly Manual 6. The rigging will now go through the rear tube in the fuselage. Note that the rigging in this
2 E-flite Fokker DVII 250 Slow Flyer Assembly ManualUsing the ManualThis manual is divided into sections to help make assembly easier to understand, a
20 E-flite Fokker DVII 250 Slow Flyer Assembly Manual 11. The rigging now heads to the rear hole in the outer strut. Again, this line will be in fro
21E-flite Fokker DVII 250 Slow Flyer Assembly Manual 16. Use the following images to verify the rigging installation. When tensioned, the lines will
22 E-flite Fokker DVII 250 Slow Flyer Assembly ManualCenter of GravityAn important part of preparing the aircraft for flight is properly balancing the
23E-flite Fokker DVII 250 Slow Flyer Assembly ManualPreflightCheck Your RadioBefore going to the field, be sure that your batteries are fully charged
24 E-flite Fokker DVII 250 Slow Flyer Assembly ManualSafety Do’s and Don’ts for Pilots• Checkallcontrolsurfacespriortoeachtakeoff.• Donot
25E-flite Fokker DVII 250 Slow Flyer Assembly ManualDAMAGE LIMITSHORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF P
26 E-flite Fokker DVII 250 Slow Flyer Assembly ManualUnited Kingdom:Electronics and engines requiring inspection or repair should be shipped to the fo
27E-flite Fokker DVII 250 Slow Flyer Assembly Manual 8. I will not operate model aircraft carrying pyrotechnic devices which explode burn, or propel
16771 Printed 10/2009Horizon Hobby USA4105 Fieldstone RoadChampaign, Illinois 61822USA(877) 504-0233Horizon Hobby UKUnits 1-4 Ployters RdStaple TyeHar
3E-flite Fokker DVII 250 Slow Flyer Assembly ManualRecommended Radio EquipmentYou will need a minimum 4-channel transmitter, receiver and two servos.
4 E-flite Fokker DVII 250 Slow Flyer Assembly ManualMotor Installation - Carbon TubeRequired PartsFuselage assemblyMotor with mounting hardwareCarbon
5E-flite Fokker DVII 250 Slow Flyer Assembly ManualMotor Installation - Firewall MountRequired PartsFuselage assemblyMotor with mounting hardwareRequi
6 E-flite Fokker DVII 250 Slow Flyer Assembly Manual 4. Slide the propeller adapter on the motor and use a .050-inch hex wrench to tighten the setsc
7E-flite Fokker DVII 250 Slow Flyer Assembly ManualServo InstallationRequired PartsFuselage Servo with hardware (2)ReceiverMicro pushrod connector (2
8 E-flite Fokker DVII 250 Slow Flyer Assembly ManualIt is best to support the fuselage with the palm of your hand while installing the servo screws. T
9E-flite Fokker DVII 250 Slow Flyer Assembly Manual 11. Use a #0 Phillips screwdriver to install the servo arm on the rudder servo. The arm will be
Kommentare zu diesen Handbüchern