E-flite Tensor 4D ARF Bedienungsanleitung

Assembly ManualTensor 4D

10 7. Slide the stabilizer forward against the horizontal fuselage. Use a square to check the alignment to the fuselage. 8. Use foam-safe CA to glue

11Radio InstallationRequired PartsFuselage assemblyMicro control connector (2)Control connector backplate (2)2mm x 4mm screw (2)Micro control horn (2)

12 2. Attach the micro control horn to the elevator using the micro control horn backplate. Place a few drops of foam-safe CA on the backplate to ens

13 3. Install the rudder control horn, making sure it is on the opposite side of the elevator horn. 4. Trim one of the servo arms from the elevator

14 6. Prepare one of the .065" x 16" carbon pushrods by attaching one of the 1/32" x 2" pushrod ends using 10" of string and

15 7. Pass the bend in the pushrod through on of the holes in the elevator control horn. Use the outer hole for minimum throw and the inner hole for

16 11. Attach the L-bend to the control horn using a micro pushrod keeper. 10. Install a micro control connector and connector backplate to the serv

17 12. Slide the pushrod end through the micro connector. Center the elevator and secure the pushrod using a 2mm x 4mm screw. 13. Repeat Steps 7 thr

18Wing InstallationRequired PartsFuselage Assembly Lower wingSide force generator (2)Required Tools and AdhesivesFoam-safe CA Hobby knifeSquare 1.

19 3. Locate the side force generators. Use a sharp hobby knife to remove the upper and lower fences from the main section. 4. Position the side for

2Table of ContentsIntroduction ... 2Specifications ...

20 6. Place the top wing onto a flat surface. Position the side force generators and fuselage onto the wing. Hold the wing flat while gluing the fuse

21Carbon Rod InstallationRequired PartsAssembled airframe.046" x 111/4” carbon rod (4).046" x 61/4" carbon rod (6)Required Tools and Ad

22 2. Slide a .046" x 111/4" carbon rod from the lower fuselage to the upper side force generator. Leave at least 1/16" of the rod exp

23 5. Slide a .046" x 111/4" carbon rod from the upper fuselage to the lower side force generator. Leave at least 1/16" of the rod exp

24 8. Install one of the .046" x 61/4" rods through the hole in the center of the side force generator and into the fuselage spine. Leave a

25 11. Locate two .046" x 61/4" carbon rods for use as the tip bracing. Glue the braces at the side force generator first, and then check t

26Aileron Servo InstallationRequired PartsAssembled airframeMicro control connector (4)Control connector backplate (4)2mm x 4mm screw (4)Micro control

27 2. Cut a hole in the bottom wing and through the vertical fuselage that will fit your particular servo. Make sure the hole is centered in the wing

28 5. Build and install the linkages using two 1/32" x 31/8" pushrods. Secure the linkages to the control horn using two micro pushrod keep

29 7. Install the remaining two micro connectors in the drilled out horns. Make sure to install the connectors opposite each other as shown. 8. Inst

3Additional Tools and AdhesivesToolsSquareHobby knifeRulerT-pinRazor sawDrill bit: 1/16", 1/8"DrillSmall Phillips screwdriverMotor/GearboxE-

30 9. Install a control horn in the bottom aileron. 10. Assemble an aileron connecting pushrod using .065" x 7" carbon rod, 1/32" x 2

31 11. Cut the carbon at the rod at the mark made in the previous step using a razor saw. Finish the assembly of the pushrod using a 1/32" x 2&q

32Installing the ElectronicsRequired PartsAssembled airframe Plywood motor mount4-40 x 3/8" socket screw (2)4-40 locknut (2) Hook and loop tape

33 3. Mount the receiver in an inconspicuous location on the fuselage spine using hook and loop or double-sided tape. Plug the elevator, rudder and a

34 5. Use hook and loop tape to secure the battery directly to the side of the fuselage behind the motor positioned to obtain the correct CG. An alt

35Landing Gear InstallationRequired PartsAssembled airframe Landing gear (2)11/2" wheel (2) Wheel stopper (2)Wheel pant (2)Required Tools and A

36 4. Position the wheels so they are parallel to the fuselage centerline. Check to make sure the installation of the landing gear is not deforming t

37Final AssemblyRequired PartsAssembled airframe.065" x 6" carbon rod (2)Upper and lower side force generator (2)Required Tools and Adhesive

38 4. Turn the plane over so it is resting on its wheels. Install the upper fences using foam-safe CA.Control ThrowsAileron: 30 degrees Up 30 degre

39Center of GravityAn important part of preparing the aircraft for flight is properly balancing the model.Caution: Do not inadvertently skip this step

4Contents of Kit/Parts LayoutLarge Replacement Parts:EFL2101 Wing Set w/StrutsEFL2102 Vertical Fuselage w/RudderEFL2103 Horizontal FuselageEFL2104

40flight is to hold the airplane vertically and advance the throttle to full power. The static thrust should be enough to make the airplane accelerate

41Large amounts of throw tend to make the airplane feel very sensitive around neutral. Because of this, it is highly recommended that you use a radio

42Left and right rudder knife-edges will require slightly different levels of mixing because of P-factor. Typically right rudder knife-edge flight req

43The Tensor is especially good at the 3D type maneuvers such as Torque Rolls, Elevators / Harriers, and High-Alpha Rolls. The large amount of aileron

44How much should you have to practice? If you are serious about learning how to hover or torque roll, work on the simulator 30 minutes to an hour eac

45Another common misnomer is that the ailerons do not work while hovering. This could not be further from the truth. If you do not use the ailerons du

2004 Official AMA National Model Aircraft Safety CodeGENERAL1) I will not fly my model aircraft in sanctioned events, air shows or model flying demons

3) At all flying sites a straight or curved line(s) must be established in front of which all flying takes place with the other side for spectators. O

7184© 2004 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 (877) 504-0233 www.horizonhobby.com

5Required Items EFLP1047 10x4.7 Slow Flyer Propeller (2)JRP4487 Quattro UL, R610UL, 2-S241JRPS241 S241 Sub-micro ServoEFLB1000 7.4v 860mAh 2-cell

6Please note that once assembly of the model has been started, you must contact Horizon Hobby, Inc. directly regarding any warranty question. Please d

7Fuselage AssemblyRequired PartsVertical fuselage Horizontal fuselageHorizontal fuselage support (2) Elevator/stabilizerCarbon elevator joiner brace

8 3. Use foam-safe CA to attach the carbon stabilizer joiner brace to the bottom of the elevator. 4. Slide the elevator/stabilizer assembly into pos

9 5. Slide the horizontal fuselage fully forward in the fuselage. Center it in the main fuselage, making sure the notch at the rear fits with the sta