E-flite Park 480 BL Motor Combo Bedienungsanleitung PDF herunterladen

Park 480 Brushless Outrunner Motor, 1020 Kv Instructions

Thank you for purchasing the E-flite Park 480 Brushless Outrunner Motor, 1020 Kv. The Park 480 Brushless Outrunner motor is designed to

deliver clean and quiet power for 3D park flyers 20- to 30-ounces (565- to 850-grams), scale park flyers 25- to 35-ounces (710- to 990-grams),

or models requiring up to 275 watts of power. It’s an especially good match for E-flite's Mini Edge 3D ARF (EFL2225) and Mini Funtana 3D

ARF (EFL2075), and would provide extreme power for sport park flyers such as the Mini Ultra Stick ARF (EFL2250).

Park 480 Brushless Outrunner Features:

• Perfect match for 3D park flyers 20- to 30-ounces (565- to 850-grams)

• Ideal for scale park flyers 25- to 35-ounces (710- to 990-grams)

• Ideal for models requiring up to 275 watts of power

• High Torque, direct drive alternative to inrunner brushless motors

• Includes mount, prop adapters, and mounting hardware

• Quiet, lightweight operation

• External rotor design, 4mm shaft can easily be reversed for alternative motor installations

• High quality construction with ball bearings and hardened steel shaft

• Slotted 12-pole outrunner design

Park 480 Specifications

Diameter: 35mm (1.4 in)

Case Length: 33mm (1.3 in)

Weight: 87g (3.1 oz)

Shaft Diameter: 4mm (.16 in)

EFLM1505

Kv: 1020 (rpms per volt)

Io: 1.1A @ 8V (no load current)

Ri: 60 mohms (resistance)

Continuous Current: 22A*

Max Burst Current: 28A*

Watts: up to 275

Cells: 6-10 Ni-MH/Ni-Cd or 2-3S Li-Po

Recommended Props: 10x7 to 12x6 ‘Electric’

Brushless ESC: 25A - 40A (EFLA312B)

* Maximum Operating Temperature: 220 degrees Fahrenheit

* Adequate cooling is required for all motor operation at maximum current levels.

* Maximum Burst Current duration is 15 seconds. Adequate time between maximum burst intervals is required for proper cooling and to avoid overheating the

motor.

* Maximum Burst Current rating is for 3D and limited motor run flights. Lack of proper throttle management may result in damage to the motor since excessive

use of burst current may overheat the motor.

Determine a Model’s Power Requirements:

1. Power can be measured in watts. For example: 1 horsepower = 746 watts

2. You determine watts by multiplying ‘volts’ times ‘amps’. Example: 10 volts x 10 amps = 100 watts

Volts x Amps = Watts

3. You can determine the power requirements of a model based on the ‘Input Watts Per Pound’ guidelines found below, using the flying weight of the model (with

battery):

• 50-70 watts per pound; Minimum level of power for decent performance, good for lightly loaded slow flyer and park flyer models

• 70-90 watts per pound; Trainer and slow flying scale models

• 90-110 watts per pound; Sport aerobatic and fast flying scale models

• 110-130 watts per pound; Advanced aerobatic and high-speed models

• 130-150 watts per pound; Lightly loaded 3D models and ducted fans

• 150-200+ watts per pound; Unlimited performance 3D models

NOTE: These guidelines were developed based upon the typical parameters of our E-flite motors. These guidelines may vary depending on other motors and

factors such as efficiency and prop size.

4. Determine the Input Watts per Pound required to achieve the desired level of performance:

Model: E-flite Mini Edge 3D ARF

Estimated Flying Weight w/Battery: 1.6 lbs

Desired Level of Performance: 150-200+ watts per pound; Unlimited performance 3D models

1.6 lbs x 150 watts per pound = 240 Input Watts of total power (minimum)

required to achieve the desired performance

1 2 3 4

Inhaltsverzeichnis

Seite 1

Park 480 Brushless Outrunner Motor, 1020 Kv Instructions Thank you for purchasing the E-flite Park 480 Brushless Outrunner Motor, 1020 Kv. The Park

Seite 2 - Examples of Airplane Setups:

5. Determine a suitable motor based on the model’s power requirements. The tips below can help you determine the power capabilities of a particular

Seite 3

Expect extreme awesome power and performance with higher speeds compared to using a 12x6 propeller. There is plenty of thrust for hovering and good v

Seite 4

1. You can first trial fit the aluminum x-mount against the front of the firewall and use a Sharpie® to mark the locations of four holes and drill ap

Kommentare zu diesen Handbüchern

Keine Kommentare

E-flite Park 480 BL Motor Combo Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Luftausrüstung E-flite Park 480 BL Motor Combo herunter. E-flite Park 480 BL Motor Combo User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Luftausrüstung E-flite Park 480 BL Motor Combo