E-flite EFL7150 Bedienerhandbuch PDF herunterladen (Seite 5)

It is extremely important to folow these transmitter setup charts to assign your

transmitter switches correctly to operate the ﬂ ight modes and Panic Recovery

correctly.

The installed AR636 receiver has been programmed for operation speciﬁ cally

in this aircraft. The ﬂ ight modes can be changed in ﬂ ight using a toggle switch

(Gear/Channel 5 Switch).

Use the provided charts to guide you through transmitter setup. Locate your

speciﬁ c transmitter in the chart and follow the numbered setup sequence. The

ending results will be:

– Toggles between ﬂ ight modes: Gear/Channel 5 Switch

– Operates Panic Recovery: Flap Switch (DX6i)

Trainer/Bind button (DX7S, DX8)

Bind button (DX6, DX9, DX18)

R-Tip (DX10t)

Non-Computerized Transmitter Setup

(DX4e and DX5e)

Before binding a non-computerized transmitter, ensure all servo reversing

is set to normal and trim is at center.

Computerized Transmitter Setup

(DX6i) • (DX7S, DX8) • (DX6, DX9 and DX18) • (DXt10)

Start all transmitter programming with a blank ACRO model (do a model

reset), then name the model.

Set Dual Rates to: HIGH 100% LOW 70%

Set Servo Travel to: 100%

DX6i

1. Go to the SETUP LIST MENU

2. Set MODEL TYPE: ACRO

3. Set REVERSE: Gear Channel

4. Go to ADJUST LIST MENU

5. Set FLAPS: Norm 100, LAND 100

Resulting in:

The Gear switch operates the 2 SAFE modes.

Gear 0: = Precision Mode

Gear 1: = 3D Mode

The Flap switch operates Panic Recovery:

Position 0=Off

Position 1=On. (not a momentary switch)

DX7S and DX8

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set SWITCH SELECT: Change all to INH:

Then TRAINER: AUX1

Then F-Mode: GEAR

4. Go to the FUNCTION LIST

5. Set SERVO SETUP: Reverse AUX1

Resulting in:

F-Mode Switch operates the 2 SAFE modes.

0 and 1 = Precision Mode

2 = 3D Mode

The Trainer/Bind button operates Panic Recovery

DX6, DX9, DX18 and DX10t

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set WING TYPE: NORMAL

4. Go to CHANNEL ASSIGN:

Channel Input Conﬁ g:

Set GEAR: B (DX10t: GEAR: A)

Set AUX1: I (DX10t: AUX1: R-TIP)

5. Go to the FUNCTION LIST

6. Set SERVO SETUP: Reverse AUX1

Resulting in:

Switch B (DX10t: A) operates the 2 SAFE modes.

0 and 1 = Precision Mode

2 = 3D Mode

The Bind/I button (DX10t: R-TIP) operates Panic

Recovery

IMPORTANT: After you set up your model, always rebind the transmitter

and receiver to set the desired failsafe positions.

Transmitter Setup for this SAFE

Technology Aircraft

DX7S/DX8

DX6i

Panic Switch

Flight Modes

Panic Switch

Flight Modes

DX10t

Flight Modes

Panic Switch

DX6, DX9, DX18

Panic Switch

Flight Modes

1 2 3 4 5 6 7 8 9 10 ... 21 22

Kommentare zu diesen Handbüchern

Keine Kommentare

E-flite EFL7150 Bedienerhandbuch Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ferngesteuertes Spielzeug E-flite EFL7150